Tungsten Weight Kit
The balance of my 365XL with these weights is next level, really nice upgrade to go with the combat grip. Noticeable difference. Thanks for the tip on the Painter's tape, worked really well.
GRIP WEIGHT KIT, TUNGSTEN, WCP320/WCP365 GRIP MODULE
$19.95
This Wilson Combat WCP320/WCP365 Tungsten weight kit is the perfect solution for those looking to enhance their recoil control and improve their firearm's balance.
This Wilson Combat WCP320/WCP365 Tungsten Weight Kit is the perfect solution for those looking to enhance their recoil control and improve their firearm's balance. The kit includes three tungsten weights that easily slide into a module to provide extra weight and greater balance while shooting your Sig P320/365. With this kit, you can customize your firearm to meet your specific needs and shooting style.
- 3 piece kit
- Adds 1.5 ounces when installed
- Drop-in compatible with all Wilson Combat WCP320 (all sizes), WCP365 (all sizes), and Sig 320 X-Compact modules
NOTE: Because these weights are a drop-in fit, apply a dab of heavy grease to prevent any potential rattle with some frames. For a more permanent installation, silicone caulk adhesive is a great choice.
Disclaimer: "SIG" is a federally registered trademark of SIG SAUER Inc. and is one of many trademarks owned by SIG SAUER Inc. Neither Wilson Combat nor this website is affiliated in any manner with or otherwise endorsed by SIG SAUER Inc. The use of "SIG" or "SIG SAUER'' on this page is merely to advertise the sale of SIG pistols, parts, or components. For genuine SIG SAUER Inc. products and parts, visit Sig Sauer.
Reviews
-
-
The Painter'S Tape Install Trick
Frank Dawkins's suggestion, below, to use painter's tape around the weights to keep them from rattling worked great! I did do something a little different, though. I had two inch tape on hand, so I cut pieces that went pretty much the entire length of the weights, one layer deep. I pushed the wrapped weights into the channels with my thumbnail, and stopped just shy of bottoming them out. That way if (for whatever reason) I wanted to remove them, I could fit a curved pick underneath the weights to push them out.
-
Great Addition For Sig P320 With Wilson X-Compact Grip Module
DON’T buy the Wilson XCompact grip module without getting these weights -very easy install -use the painter tape tip seen below to secure - REALLY improves shoot-ability and reduces muzzle flip
-
Excellent For Adding A Bit Of "Heft" To The Grip Module
I utilized blue painter's tape to wrap one end of each of the three tungsten weights before installing them in their respective channels inside the handle of the grip module. I put the open end of each weight in its channel first, then pushed down on the other end with the painter's tape wrapped tightly around the weight with the tip of a punch until each weight was all the way into its channel. There is no rattling, and you do not need to use grease or silicone to do this. And all you need is roughly one wrap around one end of each of the weights with a standard 3/4" roll of Scotch Blue Original painter's tape which can be purchased at most painting supply or home improvement stores. Again, leave one end unwrapped so it is easier to push down each weight fully into its channel all the way. Super easy!
-
Use Heat Shrink On The Upper Half Of The Pins!
These are great. As other reviewers have commented, they definitely won’t stay seated without some help. I found the perfect (non messy) solution. 1/4 heat shrink tubing for the large weight and 1/8 heat shrink tubing for the 2 smaller ones. I only put it on the upper half of each pin because I think the molding in the frame gets tighter towards the bottom. Fits snugly once shrunk around the tungsten weights! Perfect fit!
-
Tungsten Weights For P365
Along with changing to the Wilson grip model for my P365 XL, these tungsten weights have changed this pistol so much for the better. Not only for feel, but for recoil control enhancement as well. Highly recommended. BTW I read, and followed someone else’s advise to use a single wrap on blue painters masking tape instead of glue, or silicon. Fits very snuggly and I have not heard or felt a single movement.
-
Wcp365Xl
Will the weights work with the P3 65 XL
-
Great Weight
Put these on my 365xl and makes a big difference. I used the recommended silicone in the non groove rear end and then one drop of crazy glue per slot. My concern was recoil might shake them loose.
-
Excellent. Grease Em Up Good.
Excellent addition to the grip module. Make sure to use plenty of grease on the rods to keep them in place.